Scientific and Technical Journal

ELECTROTECHNIC AND COMPUTER SYSTEMS

ISSN Print 2221-3937
ISSN Online 2221-3805
IDENTIFICATION OF THE LOADING DEGREE OF THE TWO-SPEED LIFT
Abstract:

Increase of comfortable transportation, energy efficiency, safety are priority technical and economic indicators in the modernization of lift’s electric drives.Most of the lifts being operated are two-speed with a rather outdated elemental control system..The transition from an unregulated system to a regulated electric drive can significantly improve its technical characteristics, expand the functionality of the system, significantly reduce the amount of electricity consumed by the electric drive, and introduce energy-saving equipment and technologies, but at the same time, it needs a lot of money. Replacement of the outdated equipment of the control system of a two-speed electric drive on the modern allows at low material costs to get a lift that meets the high technical requirements and almost inferior to its parameters of the new kit. The main advantages of the electric drive with microprocessor-based automatic control system are high reliability, low operating costs and relatively low cost. . In that work proposed the method of determination a degree of loading of the lift depending on the starting parameters of the drive. Based on the research it was found that the determination of the degree of loading of the cab in the initial stage of the motion on the basis of transient processes at engine start-up makes it possible to improve the positioning accuracy by changing the start time of the braking and using the time delay. As a result of the performed mathematical and physical experiments,it has been proved that the developed mathematical model of the stand can be used for modeling of the real parameters of the automated control system by electric drive of the lift.Based on the conducted experiments it was obtained that the identification method allows to determine the degree of loading of a two-speed lift with an error of ± 5% with known parameters of the elevator during the time of two turnover of the motor shaft. Knowing the weight of the load this allows determine braking start time and approach of the lift’s cabin to a given stop height with minimal error which increases the comfort and quality of movement of the lift’s cabin. Further research is planned to focus on detection the impact of the variability of electrical and mechanical parameters on the quality of identification.

Authors:
Keywords
DOI
http://dx.doi.org/ 10.15276/eltecs.27.103.2018.11
References

1. Volkov, D.P. (1999), Lifts. Textbook for high schools [Lifty. Uchebnik dlya vuzov] ASV, Moscow, Russia.

2. Andryushchenko, O. A., Boyko A. O. (2011), “Increasing the technical level of passenger elevators Ukrain, evolution or revolution?”[Povishenie tekhnicheskogo urovhia pasazhirskikh liftov Ukraini, evolutsiya ili revolutsiya?], Ekonomist, no.8., pp.75-79.

3. Arkhangelskii, G. G. (2008), “Modern trends and prospects for the development of elevator construction” [Sovremennie tendentsii I perspektivi razvitiya liftostroeniya], Stroyprofile, no.7,
pp. 94-96.

4. Boyko, A. A. (2015), “Development of methodology for optimal design and operation of energy-efficient winches of passenger elevators” [Razrabotka metodologii optimalnogo proektirovaniya I ekspluatatsii energoefektivnikh lebedok pasazhirskikh liftov], Dis. Doct. tech. Sciences, 05.05.05, Odessa Ukraine.

5. Nazarova, O. S. (2017), “Investigation of the system of automatic control of the electric drive of the elevator, taking into account the loading capacity of its cab” [Doslidzhennia sistemi avtomatichnogo keruvannia elektroprivoda lifta z urakhuvanniam stupenia zavantazhennia yogo kabini], available at: http://www.av.lntu.edu.ua/c
s
v/konference_2017.pdf (accessed March 14, 2018)

6. Herman, M. V. (2017), “Prospects of microprocessor control systems for electric drive of an elevator” [Perspektyvy mikroprotsesornykh system keruvannya elektropryvodom lifta] Staliy rozvitok mist materiali X Vseukr. stud. nauk.-techn. konf. [Sustainable development of cities proceedings of the X Allukr. studio sci.-tech. conf.], Kharkiv: KhNUMG them. O. M. Beketov. - Ch. 2. –
pp. 132-133.

7. CMU Resolution No. 438 of June 21, 2017 “On Approval of the Technical Regulation of Elevators and Safety Components for Lifts” [Pro zatverdzhennia Tekhnichnogo reglamentu liftiv I komponentiv bezpeki dlia liftiv], available at: http://zakon3.rada.gov.ua/laws/show/438-2017-%D0%BF (accessed March 14, 2018)

8. Ihedioha Ahmed C., Anyanwu A.M. (2016), “Implementation of an Elevator’s Position-Controlled Electric Drive”, available at: http://www.ijtrd.com/papers/IJTRD4105.pdf
(accessed March 14, 2018)

9. Yingjie Liu, Hejun Yu, Gang Li, Zhongxing Li, Xingjun Wu. (2015), “Modeling and Simulation of the drive system of elevator based on AMESIM”, available at: http://download.atlantis-press.com/php/download_paper.php?id=25837827 (accessed March 14, 2018)

10. Stetsyuk, V.I. (2017), “Increasing the efficiency of elevator frequency converters by introducing a feedback signal” [Pidvishchennia efektivnosti roboti liftovikh peretvoruvachiv chastoti shliakhom vvedennia signal zvorotnogo zvyazku] // Bulletin of Khmelnytsky National University, No. 6, -
pp. 169-177.

11. Osadchiy, V. V. (2017), “Improvement of accuracy of positioning of two-speed elevator electric drive” [Pidvishchennia tochnosti pozitsiuvannia dvoshvidkisnogo elektroprivoda lifta], available at: http://zntu.edu.ua/uploads/dept_s&r/2017/conf/1/TN2017.pdf (accessed March 14, 2018)

Published:
Last download:
22 Aug 2019

[ © KarelWintersky ] [ All articles ] [ All authors ]
[ © Odessa National Polytechnic University, 2014-2018. Any use of information from the site is possible only under the condition that the source link! ]