Scientific and Technical Journal

ELECTROTECHNIC AND COMPUTER SYSTEMS

ISSN Print 2221-3937
ISSN Online 2221-3805
REPLACEMENT SCHEME ASYNCHRONOUS MOTORS – NEW ANGLE
Abstract:

Determining of the parameters of single-phase equivalent circuit of an induction motor based on two early developed methods by using T and G equivalent circuit is given. Algorithms of the parameters calculation by using two methods are given. The results of the calculations in a form of static mechanical and electromechanical characteristics, which were analyzed and compared, are given. Analysis of typical points of static characteristics (start, critical and nominal), gained by means of two methods in comparison with passport data of the induction motor is made. The equations of static mechanical characteristics for the first and the second method, by means of which parameters of single-phase equivalent circuit were determined and static mechanical characteristics were built are presented here. During comparing analysis of presented methods found which of them is more precise in comparison with passport data in the area of typical static characteristics points of caged induction motor.

Authors:
Keywords
DOI
10.15276/etks.15.91.2014.58
References
  1. .GOST 183-74 Mashiny jelektricheskie vrashhajushhiesja. Obshhie tehnicheskie trebovanija [GOST 183-74 Rotating Electrical Machines. General Technical Requirements], (2001), Moscow, Russian Federation, Publishing House of Standards.
  2. GOST 7217-87. Mashiny jelektricheskie vrashhajushhiesja. Dvigateli asinhronnye. Metody ispytanij. [GOST 7217-87. Rotating Electrical Machines. The Asynchronous Motors. Test Methods], (2003), Moscow, Russian Federation, Publishing House of Standards.
  3. GOST 9362-60. Jelektrodvigateli trehfaznye asinhronnye moshhnost'ju ot 100 do 1000 kVt. Tehnicheskie trebovanija [GOST 9362-60. The Three-Phase Asynchronous Electric Motors with Capacity from 100 to 1000 kW. Technical Requirements], (1960), Moscow, Russian Federation, Publishing House of Standards.
  4. GOST 18200-90. Mashiny jelektricheskie vrashhajushhiesja moshhnost'ju svyshe 200 kVt. Dvigateli sinhronnye. Obshhie tehnicheskie uslovija [GOST 18200-90. Rotating Electrical Machines with a Capacity of More than 200 kW. Synchronous Motors. General Specifications], (1991), Moscow, Russian Federation, Publishing House of Standards.
  5. DSTU 3595-97. Jelektroprivody peremennogo toka obshhego naznachenija. Obshhie tehnicheskie trebovanija. [DSTU 3595-97. The AC Drives General Purpose. General Technical Requirements, Introduction. 1998-07-01], (1998), Kiev, Ukraine, State Standard of Ukraine, 42 p.
  6. Richter R. Jelektricheskie mashiny [Electric Machines]. (1935), Moscow, Russian Federation, Vol. I – IV.
  7. Kostenko M.P., Piotrovski L.M., Jelektricheskie mashiny [Electric Machines], (1965), Vol. II, Energy.
  8. . Kovacs C.P., Ruts I. Perehodnye processy v mashinah peremennogo toka: per. s nemeckogo pod red. A. I. Vol'deka. [Transitional Processes in the Machines of Alternating Current: Transl. from German Ed. by A.I. of Valdeka], (1963), Moscow-Leningrad, Russian Federation, Gosenergoizdat, 334 p.
  9. Blashke F., (1971), Das Prinzip der Feldorientierung die Grundlage für die TRANSVEKTOR, Regelung von Drehfeldmaschinen, Siemens – Z
  10. Epstein I.I.Avtomatizirovannyj jelektroprivod peremennogo toka [Automated AC Motors], (1980), Moscow, Russian Federation, Energoizdat, 192 p.
  11. Epstein I.I. Raschet parametrov asinhronnogo dvigatelja. [Calculation of Parameters of Asynchronous motor], (2014), Energosberezhenie. Energy. Energy audit, No. 8 (126), pp. 40 – 45.
Published:
Last download:
2017-11-17 06:26:38

[ © KarelWintersky ] [ All articles ] [ All authors ]
[ © Odessa National Polytechnic University, 2014. Any use of information from the site is possible only under the condition that the source link! ]
Яндекс.Метрика